The tetrafluoroethylene-hexafluoropropylene copolymer is prescribed in ASTM D 2116, and has 4 varieties, i.e. Type I to Type IV. It's preferable that the elastomer has an potential to be modified so that a softened polyphenylene sulfide, which is prepared by mixing with the elastomer and kneading them with melting, has a flexural modulus of at most 30000 (ASTM D 790) and a tensile elongation at break of no less than 5% (ASTM D 638). Representative examples of such an elastomer are, as an example, an olefin copolymer containing an epoxy group (ethylene content: 88% by weight, glycidyl methacrylate content: 12% y weight), a hydrogenated styrenebutadience copolymer (TUFTEC M 1913 commercially available from Asahi Chemical Industry Co., Ltd.), an ethylene-propylene copolymer (TAFMER PO 680 commercially obtainable from MITSUI PETRO CHEMICAL INDUSTRIES, LTD.), and the like. The tetrafluoroethylene-perfluoroalkylvinyl ether copolymer is prescribed in ASTM D 3307, and has two varieties, i.e. Type I and kind II. The tetrafluoroethylene perfluoroalkylvinyl ether copolymer and the tetrafluoroethylenepentafluoroproylene copolymer might be employed in an extrusion molding by heating to melt. The item of the current invention is to delete the above-mentioned disadvantages of typical management cables and to provide a control cable which doesn't necessitate a lubricant to keep away from a posh coating operation and which can be utilized with clean sliding operation of the interior cable for a long period of time.

Next, use the elimination of the outdated cable to assist set up the new one. This way if you pull the previous cable out from the engine end, there shall be a threaded messenger to assist install the new alternative cable. The polyoxymethylene additionally has properties equivalent to low stickslip below a excessive load and improves the operationability of a control cable. It's preferable that the organopolysiloxane has a low viscosity in order that the organopolysiloxane can easily extide from the resin. It is particularly preferable that the content of the organopolysiloxane having an extremely-excessive viscosity is 50 to 80% by weight and the content of the organopolysiloxane having a lower viscosity is 50 to 20% by weight. The quantities of the organopolysiloxane having an extremely-high viscosity and the organopolysiloxane having a lower viscosity contained in the thermoplastic resin of the above-mentioned liner are adjusted in order that the organopolysiloxane is composed of 45 to 85% by weight of the organopolysiloxane having an extremely-high viscosity and fifty five to 15% by weight of the organopolysiloxane having a lower viscosity. However, when the viscosity of the organopolysiloxane is just too excessive, the amount of the organopolysiloxane which is extided from the floor of the resin is little, and in accordance the load efficiency and sturdiness of the control cable can't be improved sufficiently.

Also, a artificial resin coating (hereinafter known as internal coat) is about on the outer surroundings of the inner cable. Also, the organopolysiloxane could be ready to grease. When the kinematic viscosity exceeds 10000 cSt, the organopolysiloxane doesn't bleed out from the thermoplastic resin sufficiently, and the load efficiency is lowered. The representative examples of the organopolysiloxane having a lower viscosity are, for instance, dimethylpolysiloxane, methylalkylpolysiloxane, methylphenylpolysiloxane, methylaminoalkylpolysiloxane, methylfluoroalkylpolysiloxane, and the like. A thermoplastic resin shown in Tables 1 to four was heated to melt, and the organopolysiloxane obtained in the above was added thereto in a proportion proven in Tables 1 to 4. After they have been uniformly kneaded, a liner having an inside diameter of 4.6 mm and an out of doors diameter of 5.6 mm was molded. Seven steel wires are twisted to obtain one strand, and seven strands are twisted to acquire a wire rope with 7.occasions.7 development and an outside diameter of 3.Zero mm. When the melt index of the excessive density polyethylene is less than 0.01 g/10 minutes, the extrusion molding becomes tough, and there is a tendency that the internal coat can't be fixed on a stranded steel wire. Accordingly, it's preferable that the melt index is 0.01 to 5 g/10 minutes.

When the melt index of the polybutylene terephthalate is less than 0.1 g/10 minutes, it is troublesome to produce a liner by the use of an extruder, and when the melt index exceeds 5 g/10 minutes, there's a tendency that the liner is well peeled off from the conduit as a result of lack of toughness of the liner throughout forming the liner and that physical properties reminiscent of sturdiness and abrasion resistance required for the liner aren't easily exhibited. As a method for forming an internal coat through the use of the polyphenylene sulfide, as an example, a melt-extrusion methodology and an electrostatic coating method of powder may be cited. Alternatively, a considerable amount of the organopolysiloxane having a high viscosity could be contained within the resin, and the molding could be carried out without slipping. When the kinematic viscosity is less than 25 cSt, the organopolysiloxane having a lower viscosity is evaporated in a short time, and the put on and tear of the liner are generated throughout the control cable is used. Hereinafter, the control cable of the current invention and the technical effect are explained in detail with comparing some examples and comparative examples. The polymerization degrees of those types are different respectively.